Difference between revisions of "Dash Removal For L.E.D Change"
Line 94: | Line 94: | ||
− | You will notice the 4 x | + | You will notice the 4 x 10mm larger ones, these can be bought from Halfords, they are £10 for two :( . Then there are the two smaller ones, 3mm wedge, I bought these off a guy on ebay the other day, a lot cheaper. |
Well I hop this helps. | Well I hop this helps. |
Revision as of 22:49, 3 April 2007
Hey all,
As promised, another guide.
This one is mainly for the removal of the dash cluster, after that, it's straight forward to change the bulbs.
Tools Needed: Phillips screw driver Time: 30-45 mins, Can be done in under 10min. 4 x 10mm wedge L.E.D (any colour) - (501 size) 2 x 3mm wedge L.E.D (any colour)
Lets get started...
Remove all of the following srews... Underneath the climate control box:
[img]http://www.pixilive.com/uploads/20070327/Lightconversion049496.JPG[/img]
Underneath dash: 2 screws
[img]http://www.pixilive.com/uploads/20070327/Lightconversion057240.JPG[/img]
Opposite side: 2 screws
[img]http://www.pixilive.com/uploads/20070327/Lightconversion067659.JPG[/img]
underneath top of dashboard: 1 of 2
[img]http://www.pixilive.com/uploads/20070327/Lightconversion075213.JPG[/img]
Opposite side of underneath top of dashboard: 2 of 2
[img]http://www.pixilive.com/uploads/20070327/Lightconversion083586.JPG[/img]
Now remove this, gentle tug on both ends:
[img]http://www.pixilive.com/uploads/20070327/Lightconversion092964.JPG[/img]
Once removed: remove 2 screws
[img]http://www.pixilive.com/uploads/20070327/Lightconversion114812.JPG[/img]
Now you need to remove the climate control box with drivers single airvent attached: 1 of 2
[img]http://www.pixilive.com/uploads/20070327/Lightconversion123479.JPG[/img]
Opposite side: 2 of 2
[img]http://www.pixilive.com/uploads/20070327/Lightconversion138806.JPG[/img]
Once removed, these will be attached, for the lucky ones :P
[img]http://www.pixilive.com/uploads/20070327/Lightconversion142956.JPG[/img]
Once all removed should like something like this:
[img]http://www.pixilive.com/uploads/20070327/Lightconversion15.jpg[/img]
Now to remove the bit that is actually needed: Remove the following 2 of 4
[img]http://www.pixilive.com/uploads/20070327/Lightconversion16.jpg[/img]
Opposite side: 4 of 4
[img]http://www.pixilive.com/uploads/20070327/Lightconversion17.jpg[/img]
Now that those 4 screws are removed... there should be 3 large cables attached behind... once again for the lucky few :P
[img]http://www.pixilive.com/uploads/20070327/Lightconversion18.jpg[/img]
The three cables that are attached to the dash cluster:
[img]http://www.pixilive.com/uploads/20070327/Lightconversion19.jpg[/img]
Cluster should look something like this:
[img]http://www.pixilive.com/uploads/20070327/Lightconversion21.jpg[/img]
You will notice the 4 x 10mm larger ones, these can be bought from Halfords, they are £10 for two :( . Then there are the two smaller ones, 3mm wedge, I bought these off a guy on ebay the other day, a lot cheaper.
Well I hop this helps.
Matt.